LED Streetlight - IntenCity Outdoor Lighting

The IntenCity LED Streetlight

Features

Low EPA (Effective Projected Area) for lowest wind-load of any luminaire.
Wind tunnel tested to 150+ MPH winds. Unique integral Down Looking Photocell
requires no opening in housing, no wiring, and outlasts LEDs.

White LEDs with proprietary optics and control system.

Sealed light engine has no air intake and never needs internal cleaning for
Essentially Maintenance Free Outdoor Lighting.

No Ballast. High PF current regulated, solid-state power supply,
completely encapsulated for weather resistance.
Integral 7KA 180-Joule MOV transient protection.

Mounting made easy. Unique pipe mounting system ensures integrity
and seal with single-point tightening system.
No more saddle clamps or bolts to torque.

Sharp Cutoff, International Dark Sky Compliant

We are
IntenCity Lighting

Capabilities

Inside Our Products

Outdoor Lighting

IntenCity Streetlight

Sea Turtle Safe

Indoor Lighting

Interior Applications

About Parking Garages

Garage Luminaire Info

Application Tools

Photometrics & Data

Frequently Asked Questions

Community Forum

"The national average annual maintenance budget for a streetlight is typically $50. Yet too many are burning during the day, too many aren't burning at night. Imagine the cost to actually service each individual light every year, to check the photocell and clean the dirt out from inside the luminaire."

"To benefit from the efficacy of HPS lighting, luminance must be at least 3 CD/m2. This often requires more lumens which requires more energy, which offsets the perceived savings, and then ...
...you end up with ugly light."

Beware those ads:
"meets IES standards"

All lights can fall within an IES measurement type category.

ONLY IntenCity Streetlights produce 3,000+ lumens and reach 90+ feet from the pole.

sometimes spelled
- street light
- street lamp

Specifications

Lighting System
Light Emitting Diodes
Input Power
70VA, PF > 0.95
Operating Voltage
100 to 277VAC, 47 to 63 Hz.
Humidity
0 - 99%
Dust and Moisture
IP66 rating (no intrusion)
Operating Temperature
-40° C to 55° C
(electronics to 70°C)
Storage Temperature
-40° C to 85° C
Finish
Black Anodized
Dimensions
4 3/8" H x 16" W x 17.5" L
Mounting
Single-point tightener to existing 1.5" or 2" pipe
Weight
13 lbs
Connections
3x 12" 16 AWG wire leads
Photocell
ON < 1 foot-candle, OFF @ > 1.5
Emission Color
4,700° K CCT
Lumens
approx. 2,438
Compliance to Codes & Standards
UL-C, NEC, NEMA,
FCC Part 15 Class B

General
Light weight. Sharp optical cutoff, limited trespass, non-glare, 10+ year design life. Lumen Maintenance 70% after 50,000 hours at 30° C ambient.

Construction
Heavy gauge aluminum extrusion, black anodized finish. Injection molded polycarbonate lens with gasket seal. Door opens for electrical connections and installation.

Applications
Solid-state lighting system for:
- Replacement of HPS, Mercury Vapor
- Coastal model for Sea Turtle habitat
- Tropical storm areas
- Parking lots
- High vibration bridges & tunnels
- Sub-zero temperatures

Replaces 100 watt High Pressure Sodium luminaires for half the energy.

Installation
Luminaire mounts to standard pipe size fitting of streetlight mast or pole with proprietary single-point tightening system. Three wire electrical connection. Photocell is active in all units, may be defeated if desired.

Options
LED color: 590nm, Cool White
Building/Wall mounting

See Photometrics page for data sheets and IES files.

maintenance free international dark sky compliant LED streetlights